Different Series Aluminum Alloy Bar, Aluminum Round Bar, Aluminum Solid Bar

2000 Series: 2011,2A12,2014,2017,2024
5000 Series: 5052,5652,5154,5254,5454,5056,5082,5182,5083,5086,5N01,5N02
6000 Series: 6106,6201,6011,6351,6005,6060,6061,6063,6082,6083,6463,6262
7000 Series: 7003,7005,7020,7050,7075,7A04

Different Treatment:
1. O Condition.
2. H Condition: H111/H112/H113/H13.
3. T Condition: T3/T351/T4/T5/T6/T651/T6511/T73/T7351/T7651/T76511.

2011/2A12/2014/2017/2024 Aluminum Alloy Bar Aluminum Round Bar

2024 aluminum bar, aluminum rod is a typical hard aluminum alloy in the aluminum-copper-magnesium series. Its composition is reasonable and its comprehensive performance is good. This alloy is produced in many countries and is the largest amount of hard aluminum.


The alloy can be used as working parts below 150 ° C. The strength of 2024 alloy is higher than that of 7075 alloy. The forming performance is better in the hot state, annealing and new quenching states, and the heat treatment strengthening effect is significant, but the heat treatment process is strict. Poor corrosion resistance, but covered with pure aluminum can be effectively protected; cracks are easy to occur during welding, but special processes can be used for welding and riveting.


2024 aluminum bar,aluminum rod is a high-strength hard aluminum, which can be strengthened by heat treatment. It has moderate plasticity in the quenched and freshly quenched state. It has good spot welding and has the tendency to form intergranular cracks when gas welding. The cutting performance is good, and the machinability after annealing is low: the corrosion resistance is not high. Anodizing treatment and painting methods are often used or the surface is coated with an aluminum layer to improve its corrosion resistance.

2024 is mainly used to make various high-load parts and components (but not including stamping parts and forgings) such as skeleton parts, skins, bulkheads, ribs, spar, rivets and other working parts below 150 ºC on aircraft.




Chemical Composition
 
Mechanical Properties
 



5052/5083/5005/5A05 Good Corrosion Resistance and Weldability Aluminum Bar Aluminum Alloy Bar

5052 aluminum alloy is a kind of Al Mg alloy, which is widely used, especially in the construction industry. It is the most promising alloy. It has good corrosion resistance, weldability, cold workability and medium strength. The main alloy element of 5052 aluminum alloy is magnesium, which has good forming and processing performance, corrosion resistance, weldability and medium strength. It is used to manufacture aircraft oil tank, oil pipe, as well as sheet metal parts of traffic vehicles and ships, instruments, street lamp bracket and rivets, hardware products, electric appliance outer shell, etc.



5052 aluminum alloy is the most widely used antirust aluminum, which has high strength, especially fatigue strength: high plasticity and corrosion resistance, can not be strengthened by heat treatment, good plasticity in semi cold work hardening, low plasticity in cold work hardening, good corrosion resistance, good weldability, poor machinability and polishing. It is mainly used for low load parts that require high plasticity and good weldability and work in liquid or gas medium, such as oil tank, gasoline or lubricating oil conduit, various liquid containers and other small load parts made by deep drawing: wire rod is used for rivets.



Chemical Composition

Aluminum al: margin
Silicon Si: ≤ 0.25
Copper Cu: ≤ 0.10
Mg: 2.2 ~ 2.8
Zinc Zn: ≤ 0.10
Manganese Mn: ≤ 0.10
Cr: 0.15-0.35
Iron Fe: ≤ 0.40
Note: single: < 0.05; total: < 0.15
 


Aluminum Bar: Diameter φ8 - φ460. Length: 1~6 meters.

Aluminum Tube: (diameter φ10 - φ460, wall thickness 0.3-40mm)
Pure aluminum tube, alloy aluminum tube, seamless aluminum tube (extrusion, drawing), large diameter aluminum tube, thick wall aluminum tube, alumina tube, aluminum flat tube, aluminum square tube, elliptical tube, coil, fine pull Pull out the aluminum tube.



Technical Parameter



6060/6061/6063/6082/6083 T351/T4/T5/T6/T651/T6511 Aluminum Alloy Bar Aluminum Round Bar

6063 series aluminum bar, aluminum rod, aluminum alloy bar, aluminum alloy rod by the company is a low-alloyed Al-Mg-Si high-plastic alloy. It has many valuable features as follows:

1.Heat treatment strengthening, high impact toughness.


2.There is excellent thermoplasticity, which can be kneaded at high speed into a messy layout, various profiles of thin-walled hollow or forged forgings with complicated layout, wide quenching temperature, low quenching sensitivity, kneading and casting after demoulding only The temperature is required to be higher than the quenching temperature. That is, it can be quenched by spraying water or water. Thin-walled parts (6<3mm) are also capable of wind quenching.


3.The welding function and corrosion resistance are excellent, and there is no stress corrosion cracking tendency. In the heat-treated reinforced aluminum alloy, the Al-Mg-Si alloy is an alloy in which only the stress corrosion cracking appearance is not found. Fourth, the appearance after processing is very bright, and simple anodizing and coloring.



Chemical Composition
  

Mechanical Properties